??

No Third-party Cookies supported

Your browser does not allow setting Third-party cookies. Please enable them in your browsers settings or click the button below.

Please enable cookies in your browser for PARTcommunity to work
Catalog navigation
All catalogs
Geometric Search
Sketch Search
Variable Search
Certified catalogs
By Categories
By Countries
By Standards
en

HFSV6-3030-50

  1. Misumi
  3. metric
  5. 38_al_extrusions_blackets
  7. Aluminum Frames 2
CAD model selection
Selectable products: 2
HELP_VARIABLE
Company
Misumi
Description
HFSV6-3030, HFSV6-3060 - HFS6 Series Aluminum Extrusions -Minimal Corner Radius Extrusions-
Bill of material
HFSV6-3030-50
Part Number
Type and Frame Selection
Material
A6N01SS-T5 Aluminum Alloy
Surface Treatment
Clear Anodize
L 0.5mm Increment
 mm
Enter value for L
L 0.5mm Increment
mm
cm
inch
ft
Mass
kg/m
Sectional Area
mm2
Cross Sectional Moment of Inertia - lx
mm4
Cross Sectional Moment of Inertia - ly
mm4
Tapping
Depth on the Left Side
0 mm
Depth on the Right Side
0 mm
Tapping (Heli-Coil Insert)
M
0
Depth
0 mm
Tapping (Corner Section)
M
0
Depth
0 mm
High Precision Cut
45 Degree Cuts
Cutting Position Selection
Cutting Direction Selection for Left Side
Cutting Direction Selection for Right Side
Fastening Location Wrench Access Hole Alterations
Location Specified Wrench Access Hole Alteratons (Horizontal)
Location Specified Wrench Access Hole Alteratons (Vertical)
Location Specified Wrench Access Hole Alteratons (Crisscross)
DD6 Specification
d
 mm
Hole Position Selection
Number of Left Side Hole
Hole Direction Selection for Left Side
Number of Right Side Hole
Hole Direction Selection for Right Side
H (Left)
0 mm
H (Right)
0 mm
J
0 mm
K
0 mm
Available Alteration Combinations (Fastening Location Wrench Access Hole on The Left Side)
Available Alteration Combinations (Fastening Location Wrench Access Hole on The Right Side)
Number of Hole (Horizontal)
AH 0.5mm Increment
 mm
BH 0.5mm Increment
 mm
CH 0.5mm Increment
 mm
DH 0.5mm Increment
 mm
EH 0.5mm Increment
 mm
Number of Hole (Vertical)
AV 0.5mm Increment
 mm
BV 0.5mm Increment
 mm
CV 0.5mm Increment
 mm
DV 0.5mm Increment
 mm
EV 0.5mm Increment
 mm
Number of Hole (Crisscross)
AP 0.5mm Increment
 mm
BP 0.5mm Increment
 mm
CP 0.5mm Increment
 mm
DP 0.5mm Increment
 mm
EP 0.5mm Increment
 mm
Counterbore Hole in Specified Position (Vertical)
Counterbore Hole in Specified Position (Horizontal)
Z
d
0.0 mm
d1
0.0 mm
Number of Hole (Vertical)
XA 0.5mm Increment
 mm
XB 0.5mm Increment
 mm
XC 0.5mm Increment
 mm
XD 0.5mm Increment
 mm
XE 0.5mm Increment
 mm
Number of Hole (Horizontal)
YA 0.5mm Increment
 mm
YB 0.5mm Increment
 mm
YC 0.5mm Increment
 mm
YD 0.5mm Increment
 mm
YE 0.5mm Increment
 mm
D Type Hole Alteration
Hole Position Selection
Hole Direction Selection for Left Side
Hole Direction Selection for Right Side
H
0 mm
D
0.0 mm
S Type Hole Alteration
Hole Position Selection
Hole Direction Selection for Left Side
Hole Direction Selection for Right Side
H
0 mm
D1
0.0 mm
D2
0.0 mm
M Type Hole Alteration
Hole Position Selection
Hole Direction Selection for Left Side
Hole Direction Selection for Right Side
H1
0 mm
D
0.0 mm
L Type Hole Alteration (Top)
H (Hole Qty.)
JLP 1mm Increment
 mm
D
0.0 mm
L Type Hole Alteration (Bottom)
H (Hole Qty.)
KLP 1mm Increment
 mm
D
0.0 mm
End Face C Chamfering
Previews
3D
Dimension
2D
Download CAD models